The LNB for the OSCAR 100 downlink receiver was sealed after the modification, and has replaced the temporary one mounted at the 60cm dish.
I still need to complete the indoor buffer circuit, but some preparations for other stuff had to be done first.
Next comes the transmitter up-converter to 2.4GHz. I am still waiting for a passive mixer module specified up to at least 2.5GHz, and they are on the way.
The configuration will likely be as follows:
432/439MHz transceiver frequency -->
attenuator and the LO *) signal -->
Passive Mixer -->
amplifier, probably made with the RF amplifier of a modified (filters) MMDS converter (when using 432/439MHz as IF, these filters should provide sufficient image rejection) -->
20 - 50mW amplifier -->
1W amplifier -->
cable to feed antenna system -->
"8W" amplifier, likely providing 4-5W at the feed -->
feed antenna --> dish antenna **)
*) LO signal provided by a ADF4350 synthesizer board controlled by an Arduino Uno board -->
about 20mW amplifier at 1962/1968MHz.
**) experiments with other antennas will be done. I already have a panel antenna for RHCP and a 1m long yagi, as well as a cheap, probably not very good, 17elm yagi about 40cm long, as well as a PCB LPDA antenna for test as a feed antenna.
This should provide a decent up-link signal to OSCAR 100, useable for SSB, and certainly for CW or digital modes.
The building activities will be halted for a few weeks, but mid april they should resume.
More than enough experimentation before the refinement of the system starts.
The buffer for the RX reference LO should be ready and tested soon, though.
Showing posts with label inexpensive Chinese modules.. Show all posts
Showing posts with label inexpensive Chinese modules.. Show all posts
2019-02-18
Es'hail 2 Sattellite, aka Qatar OSCAR 100
The Es'hail 2 satellite has been launched and has entered geostationary orbit. This satellite has TV transponders, and something new for radio amateurs : a 2400MHz to 10GHz transponder in geostationary orbit.
The coverage should be all of Europe and Africa, to the East into India, and to the West a tiny bit of Brazil. Even Antarctica should be within range, if some of the research stations are within the footprint of the satellite I assume that some testing will be going on before the transponders go online, but this is an exciting time for radio amateurs interested in satellite communication.
First update:
The sat is in orbit and the amateur radio transponders are now operational.
They work very well. An SSB uplink with 60cm dish antenna and linear polarization produces a readable signal, a around 10-20 dB above the noise, as I have heard on the WebSDR.
On the spectrum of the WebSDR it is even possible to see the effect of running too much uplink power. This creates dark bands on the waterfall spectrum, and sometimes audible attenuation of received signals.
Frequency stability is the main problem with the uplink and downlink, for obvious reasons.
As a first attempt at working through the satellite I was thinking of purchasing a relatively low cost up converter from SG-Labs in Bulgaria for the uplink. This has about 500mW output, and with a 1W power amplifier at the feed point it should be possible to be heard via the transponder with SSB, and certainly with CW.
A fun experiment would be trying FT8 or JT65 with a much lower ERP.
Receiver side will be with a low noise satellite PLL LNB, possibly with a later modification of the reference oscillator.
I have decided to take time to attempt a simple up converter made of Chinese modules available on eBay.
Second update :
10GHz reception converter (arriving shortly) for downlink:
LNB suitable for OSCAR 100 reception has arrived. Octagon OSLO (PLL controlled Local oscillator.
Initial test will be done with the unmodified LNB.
It will need a modification for better suitability: External reference oscillator, preferably a TCXO, at a stable temperature, fed through the cable (disconnect the internal XO, info on the Internet).
Alternatively, for even better stability, a GPS locked oscillator could be used.
2.4GHz uplink:
Modules from China have been ordered :
1) Synthesizer : ADF4350, covers 137MHz - 4.4GHz Needs to be programmed. There seems to be a library for the Arduino microcontroller. Price per unit about 10 GBP
It turns out, looking through my stock that I have a single AD4350 and an Arduino UNO, so it is possible to start the process of building the local oscillator for the transmit converter. Now for learning some Arduino (variant of C) coding.I ordered a few mor ADF4350s as spares in case I have an accident of destroying the one I have.
Learning the coding could easily take the time needed for the stuff from China to arrive, unless I find a suitable program that just needs a simple modification. No need to invent everything all over again.
2) Passive up (and down) converter modules (also to have some spares). Price per unit about 8 GBP
3) 1W amplifier modules. Price about 10 GBP
I ordered a few, because I have a long run of cable, and would like to have one as output for the indoor unit, and one at the antenna feed point.
The official uplink power for the satellite is regarded to be about 10W into a 60 - 90cm dish. However, an output of 1W appears to be sufficient to make SSB contacts via the satellite, as I have heard several stations with similar set-ups via the WebSDR.
4) Double balanced RF mixer (down conversion) Price about 5 GBP.
Why a down converter ? Well, it is a simple addition adding receive functionality, creating not just a satellite uplink transmit converter, but getting a 2400MHz transverter, making simple two-way contacts possible on that band, albeit with low power. It will most likely be possible to make some local contacts, and possibly a bit more during tropo conditions.
I already have some amplifiers capable of an output of about 100mW on the band, more than sufficient drive for the 1W amplifier mentioned above. Those were priced about 5 GBP.
One more thing is needed for this to work without making interference. A band pass filter.
I need to look into the best solution for that.
If (when) I succeed in getting a signal through the satellite, the adventure begins. Optimization of all aspects of reception and transmission, and experiments with very low power. I was told by OZ2OE that he had heard a Dutch station running a 75mW CW signal into a 1m dish, and it was audible at 539.
Also, running 1W into a much smaller antenna is an idea I want to play with. I have a tiny Wifi yagi, 40cm boom length and 17 elements. That will be an interesting comparison with the 80cm dish I have, and a good comparison. Constant gain from the yagi, and seeing the different improvements to the dish and feed.
I see quite a bit of experiments and lots of optimization in my future.
The coverage should be all of Europe and Africa, to the East into India, and to the West a tiny bit of Brazil. Even Antarctica should be within range, if some of the research stations are within the footprint of the satellite I assume that some testing will be going on before the transponders go online, but this is an exciting time for radio amateurs interested in satellite communication.
First update:
The sat is in orbit and the amateur radio transponders are now operational.
They work very well. An SSB uplink with 60cm dish antenna and linear polarization produces a readable signal, a around 10-20 dB above the noise, as I have heard on the WebSDR.
On the spectrum of the WebSDR it is even possible to see the effect of running too much uplink power. This creates dark bands on the waterfall spectrum, and sometimes audible attenuation of received signals.
Frequency stability is the main problem with the uplink and downlink, for obvious reasons.
As a first attempt at working through the satellite I was thinking of purchasing a relatively low cost up converter from SG-Labs in Bulgaria for the uplink. This has about 500mW output, and with a 1W power amplifier at the feed point it should be possible to be heard via the transponder with SSB, and certainly with CW.
A fun experiment would be trying FT8 or JT65 with a much lower ERP.
Receiver side will be with a low noise satellite PLL LNB, possibly with a later modification of the reference oscillator.
I have decided to take time to attempt a simple up converter made of Chinese modules available on eBay.
Second update :
10GHz reception converter (arriving shortly) for downlink:
LNB suitable for OSCAR 100 reception has arrived. Octagon OSLO (PLL controlled Local oscillator.
Initial test will be done with the unmodified LNB.
It will need a modification for better suitability: External reference oscillator, preferably a TCXO, at a stable temperature, fed through the cable (disconnect the internal XO, info on the Internet).
Alternatively, for even better stability, a GPS locked oscillator could be used.
2.4GHz uplink:
Modules from China have been ordered :
1) Synthesizer : ADF4350, covers 137MHz - 4.4GHz Needs to be programmed. There seems to be a library for the Arduino microcontroller. Price per unit about 10 GBP
It turns out, looking through my stock that I have a single AD4350 and an Arduino UNO, so it is possible to start the process of building the local oscillator for the transmit converter. Now for learning some Arduino (variant of C) coding.I ordered a few mor ADF4350s as spares in case I have an accident of destroying the one I have.
Learning the coding could easily take the time needed for the stuff from China to arrive, unless I find a suitable program that just needs a simple modification. No need to invent everything all over again.
2) Passive up (and down) converter modules (also to have some spares). Price per unit about 8 GBP
3) 1W amplifier modules. Price about 10 GBP
I ordered a few, because I have a long run of cable, and would like to have one as output for the indoor unit, and one at the antenna feed point.
The official uplink power for the satellite is regarded to be about 10W into a 60 - 90cm dish. However, an output of 1W appears to be sufficient to make SSB contacts via the satellite, as I have heard several stations with similar set-ups via the WebSDR.
4) Double balanced RF mixer (down conversion) Price about 5 GBP.
Why a down converter ? Well, it is a simple addition adding receive functionality, creating not just a satellite uplink transmit converter, but getting a 2400MHz transverter, making simple two-way contacts possible on that band, albeit with low power. It will most likely be possible to make some local contacts, and possibly a bit more during tropo conditions.
I already have some amplifiers capable of an output of about 100mW on the band, more than sufficient drive for the 1W amplifier mentioned above. Those were priced about 5 GBP.
One more thing is needed for this to work without making interference. A band pass filter.
I need to look into the best solution for that.
If (when) I succeed in getting a signal through the satellite, the adventure begins. Optimization of all aspects of reception and transmission, and experiments with very low power. I was told by OZ2OE that he had heard a Dutch station running a 75mW CW signal into a 1m dish, and it was audible at 539.
Also, running 1W into a much smaller antenna is an idea I want to play with. I have a tiny Wifi yagi, 40cm boom length and 17 elements. That will be an interesting comparison with the 80cm dish I have, and a good comparison. Constant gain from the yagi, and seeing the different improvements to the dish and feed.
I see quite a bit of experiments and lots of optimization in my future.
Subscribe to:
Posts (Atom)